South Carolina pricing
Roofing Calculator: Squares from Roof Area — South Carolina
Enter the area you measured and the roof pitch. This tool converts it into roofing squares — the unit every roofer quotes in — and shows what those squares cost in your market. Every figure below is already adjusted for South Carolina labor and material pricing.
Model reviewed August 2026
Does roofing squares cost more in South Carolina?
-8% versus the national baseline
Installed prices in South Carolina run about 8% below the national baseline. Permit fees are about 10% lower than the national average. Homeowner permits allowed on owner-occupied property.
Charleston and Horry County enforce coastal wind and elevation rules plus historic review; upstate Greenville prices and permits like the interior Southeast.
Ground footprint under the roof, or the sloped surface if you measured on the roof.
10% for a simple gable roof, 15% for a cut-up roof with many valleys and hips.
National baseline for architectural shingles. Pick a state above to re-price it.
Roofing squares
26.9
1 square = 100 sq ft of roof surface
- Squares to orderIncludes 10% waste
- 29.6 squares
- Roof surface area
- 2,688 sq ft
- Shingle bundles (3 per square)
- 89 bundles
- Estimated installed costMaterials and labor, before tear-off and permit
- $15,560 – $22,102
Estimates only. Local pricing, site conditions and code requirements change the real number.
What changes the number in South Carolina
| Local cost indexBelow the national baseline | 0.92x national |
|---|---|
| Permit fee index | 0.90x national |
| Code basisStatewide code applies | South Carolina Residential Code, based on the IRC |
| Owner-builder posture | Homeowner permits allowed on owner-occupied property |
| Largest markets | Charleston, Columbia, Greenville, Myrtle Beach |
The formula
Squares = (area x pitch multiplier) / 100; Squares with waste = squares x (1 + waste %)
One roofing square is exactly 100 square feet of roof surface. If you measured the ground footprint rather than the sloped roof, the pitch multiplier converts it to actual surface area; if you already measured on the roof, choose the flat option.
Covered markets in South Carolina
City-level cost and permit pages with local building department links.
Frequently asked questions
How many square feet is a roofing square?
Exactly 100 square feet of roof surface. A 30-square roof is 3,000 square feet of sloped surface, not floor area.
How do I calculate roofing squares from my house size?
Multiply the ground footprint by a pitch multiplier (about 1.06 for a low slope, 1.12 for a 6:12, 1.25 for an 8:12 and up to 1.4 for very steep), then divide by 100.
How many squares is a 2,000 sq ft roof?
A measured 2,000 sq ft roof surface is 20 squares. A 2,000 sq ft footprint usually works out to 21 to 28 squares once pitch and overhangs are counted.
How many bundles of shingles per square?
Three bundles cover one square for standard 3-tab and architectural shingles. Heavier designer and premium shingles can take four or five bundles per square.
Should I add waste to my square count?
Yes. Order 10% extra on a simple gable roof and 15% on a roof with multiple valleys, hips, dormers or skylights so cuts and starter courses do not leave you short.
Sources
Sources & verification
- South Carolina LLR Building Codes Council
- NRCA roofing installation standards
- ASTM shingle and underlayment specifications
- International Residential Code — roof assemblies (R905)
- International Code Council (IRC/IBC)
Model vintage August 2026. The links above are the issuing agencies' own pages — we publish them so you can confirm the current rule yourself, not as evidence that each fact on this page was re-checked with them today. Cost figures are modeled estimates based on national baselines adjusted for local labor and material pricing, not quotes. Permit rules change; confirm with the building department before starting work.